WEG CFW-09 User Manual Page 153
- Page / 362
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
154
CHAPTER 6 - DETAILED PARAMETER DESCRIPTION
Figure 6.24 -Copying the parameters from the “Inverter A” to the “Inverter B”
Range
[Factory Setting]
Parameter Unit Description / Notes
Parameters
Parameters
EEPROMEEPROM
INVERTER
B
INVERTER
A
INVkeypad
P215 = 1
Press
KeypadKeypad
keypadINV
P215 = 2
Press
P216 32 to 127
ReferenceEngineering [ 112 = p ]
Unit 2 -
P217 32 to 127
ReferenceEngineering [ 109 = m ]
Unit 3 -
These parameters are useful only for inverters provided with a keypad
with LCD display.
The engineering unit of the speed reference is composed of three
characters, which will be displayed on the indication of the Speed
Reference (P001) and Motor Speed (P002). P207 defines the left
character, P216 the center character and P217 the right character.
For more details, refer to Parameter P207.
While the Keypad runs the reading or writing procedures, it cannot be
operated.
This parameter is useful only for inverters provided with a keypad with
LCD display.
It allows the adjustment of the LCD Display contrast. Increase/decrease
the parameter content to obtain the best contrast.
P218 0 to 150
LCD Display [ 127 ]
ContrastAdjustment -
P220
(1)
0 to 10
LOCAL/REMOTE [ 2 ]
Selection Source -
Defines the source of the LOCAL / REMOTE selection command.
- FREQUENCY 2
- INVERTER 2
- Summary of Revisions 3
- Safety Notices 4
- General Information 4
- Installation and Connection 4
- Keypad (HMI) Operation 5
- Start-up 5
- Technical Specification 7
- -999 to +999 0 - 143 10
- -100.0 to +100.0 0.0 % 165 14
- -100.0 to +100.0 0.0 % 167 15
- -100.0 to +100.0 0.0 % 168 15
- -100.0 to +100.0 0.0 % 169 15
- User's 26
- Setting Setting 26
- II. Fault Messages 32
- III. Other Messages 33
- SAFETY NOTICES 34
- CHAPTER 1 34
- GENERAL INFORMATION 36
- CHAPTER 2 36
- FRONTVIEW VIEW-A 38
- 2.5 RECEIVINGAND 40
- INSTALLATION AND CONNECTION 41
- CHAPTER 3 41
- 3.1.3 Mounting Specifications 42
- 3.1.3.2 Mounting on Surface 44
- 3.1.3.3 Mounting with the 45
- Heatsink Through 45
- 3.1.4 Keypad (HMI) and 47
- Cover Removal 47
- 3.2.2 Location of the Power/ 50
- Grounding/Control 50
- Connections 50
- 3.2.3 Rated Voltage Selection 52
- 3.2.4 Power/Grounding Wiring 53
- R S T U V W 56
- PE W V U 56
- 3.2.5.3 Grounding Connections 57
- 3.2.5.2 Output Connections 57
- 3.2.5.4 IT Networks 58
- 3.2.6 Control Wiring 60
- * Can be used for grounding 62
- 3.2.7 Typical Terminal 63
- 3.3.2 Epcos Filters 67
- 380-480 V power supply: 68
- 500-600 V power supply: 69
- 660-690 V power supply: 69
- 3.3.3 Schaffner Filters 70
- 220-230 V power supply: 72
- FRONTVIEW 83
- MECHANICAL DATA SIDE VIEW 83
- Bus bar connection(Type/99) 84
- Series FN 2259 84
- KEYPAD (HMI) OPERATION 85
- CHAPTER 4 85
- 4.2.1 Keypad Operation 87
- 4.2 USE OF THE KEYPAD 87
- 4.2.2 “Read-Only” Variables 88
- 4.2.3 Parameter Viewing and 89
- Programming 89
- (1) (2) (3) 90
- CHAPTER 5 92
- START-UP 92
- ORIENTED START-UP 93
- 5.3 START-UP 97
- 5.3.1 Type of Control: 98
- V/F 60 Hz - Operation 98
- Via Keypad (HMI) 98
- (Operation Via Keypad 101
- Ventilation Type 106
- Motor Speed 107
- ATTENTION! 108
- 5.3.3 Type of Control: 108
- VVW - Keypad 108
- Operation 108
- CHAPTER 6 116
- DI1 to DI8 Status 119
- P012 = 10010000 119
- DO1 to RL3 Status 119
- P013 = 00101 119
- Hours Energized 121
- P042 = 22 h 121
- (2) (11) 126
- 135
- (2) (7) (12) 138
- Regulator 141
- P166 Differential Gain Action 142
- 0.01 to 7.99 On 142
- (1)(2)(11) 146
- P204 = 5 147
- (y´ = 7)] 152
- % and Gain = 1.00: 163
- V/Hz - P300, P301 and P302 195
- Loss Recover (P323) 201
- Line Loss (P321) 201
- Ride-Through (P322) 201
- Undervoltage (75 %) 201
- N = Real Speed 211
- P398 Function 212
- (1) (2) (11) 213
- (1) (11) 213
- (1) (12) 213
- 1)[s(eKp)s(y 219
- DIx Operating Mode 220
- 0 (0 V) Manual 220
- 1 (24 V) Automatic 220
- P527 Action Type 223
- 0 Direct 223
- 1 Reverse 223
- Table 6.67 - PID action type 223
- P536 Action Type 226
- 0 Active 226
- 1 Inactive 226
- CHAPTER 7 227
- 7.2 TROUBLESHOOTING 232
- 7.4.1 Cleaning Instructions 235
- 7.5 SPARE PART LIST 236
- Models 220-230 V 237
- Models 380-480 V 238
- Models 500-600 V 241
- Models 500-690 V 244
- Models 660-690 V 245
- CHAPTER 8 247
- EBA BOARD 249
- CC9 Board 249
- M3 x 8 Screw 249
- 1Nm Torque 249
- 8.1.2 EBB 250
- (Expansion I/O Board B) 250
- 8.2 INCREMENTAL 253
- 8.2.1 EBA/EBB Boards 253
- 8.1.3 EBE 253
- 8.2.2 EBC1 Board 255
- 8.4 REMOTE KEYPAD 257
- AND CABLES 257
- 8.3 KEYPAD WITH 257
- LEDs ONLY 257
- 8.6 RS-232 PC 261
- COMMUNICATION KIT 261
- 8.5 BLANK COVERS 261
- 8.7 LINE REACTOR / 262
- DC BUS CHOKE 262
- DC- EQUIVALENT 263
- AC Input 264
- PE R S T U V W PE 264
- 8.9 RFI FILTER 266
- 8.8 LOAD REACTOR 266
- 8.10 DYNAMIC BRAKING 267
- 8.10.1 DB Resistor Sizing 267
- 8.10.2 Installation 269
- DBW-01 and DBW-02 270
- 8.10.3.1 DBW-01 and DBW-02 271
- Identification Label 271
- DBW-01 DBW-02Dimension A 272
- 252 (9.92) 277 (10.91) 272
- Figure 8.30 - Power terminals 274
- 8.12 FIELDBUS 276
- 8.11 THROUGH SURFACE 276
- MOUNTING KIT 276
- 8.12.1 Installation of the 277
- Fieldbus kit 277
- DEVICENET PROFIBUS DP 279
- 8.12.2 Profibus DP 280
- 8.12.3 Profibus DP-V1 282
- 8.12.4 DeviceNet 283
- 8.12.5 DeviceNet Drive 285
- 8.12.6 EtherNet/IP 286
- 1 2 3 4 5 6 7 8 291
- (MSB) (LSB) 291
- 8.12.7.2 Variables Written 295
- 8.12.7.3 Fault Indications 297
- 8.12.7.4 Addressing of the 298
- CFW-09 Variables 298
- 8.13 SERIAL COMMUNICATION 299
- 8.13.1 Introduction 299
- 8.13.2 Interfaces Description 300
- 8.13.2.1 RS-485 300
- 8.13.2.2 RS-232 301
- 8.13.3 Protocol Definitions 301
- 8.13.3.1 Used Terms 301
- 8.13.3.2 Parameters/Variables 302
- Resolution 302
- 8.13.3.3 Characters 302
- 8.13.3.4 Protocol 302
- 8.13.3.5 Execution and 304
- Telegram Test 304
- 8.13.3.6 Telegram Sequence 305
- 8.13.3.7 Variable Code 305
- 8.13.4 Telegram Examples 305
- 8.13.5 Variables and Errors 306
- Communication 306
- 8.13.5.1 Basic Variables 306
- 7 6 5 4 3 2 1 0 308
- 8.13.5.3 Parameters Related 310
- Serial Communication 311
- 8.13.6 Times for Read/Write 311
- 8.13.7 Physical Connection 312
- Interface 312
- 8.14.3 Detailed Function 319
- Description 319
- 8.14.3.1 Function 01 320
- Read Coils 320
- 8.14.3.2 Function 03 - Read 320
- Holding Register 320
- 8.14.3.3 Function 05 - Write 321
- Single Coil 321
- 8.14.3.4 Function 06 - Write 322
- Single Register 322
- 8.14.3.5 Function 15 - Write 323
- Multiple Coils 323
- 8.14.3.6 Function 16 - Write 324
- Multiple Registers 324
- 8.14.3.7 Function 43 - Read 325
- Device Identification 325
- 8.14.4 Communication Errors 326
- 8.14.4.1 Error Messages 326
- 8.15 KIT KME (for Extractable 328
- Mounting) 328
- 8.16.3 Electrical 331
- Installation 331
- 8.16.4 Closing the Inverter 331
- Input Reat 332
- 8.19 PLC BOARD 334
- CHAPTER 9 335
- TECHNICAL SPECIFICATIONS 335
- 9.1.2 220-230 V Power Supply 336
- 9.1.3 380-480 V Power Supply 336
- 9.1.4 500-600 V Power Supply 337
- Note: CT = Constant Torque 338
- VT = Variable Torque 338
- Factory Default 338
- 9.1.5 660-690 V Power Supply 339
- 9.2 ELECTRONICS/GENERAL DATA 342
- 9.2.1 Applicable Standards 343
- 9.4 MECHANICAL DATA 345
- SIZE 8 AND 8E 352
- 412 (16.22) 353
- 275 (2.83) 353
- 68.5 (2.70) 353
- 14 (0.55) 353
- SIZE 10 AND 10E 355
Comments to this Manuals
Related products and manuals for Power adapters & inverters WEG CFW-09
(40 pages)
(79 pages)© 2020, manymanuals.com. All rights reserved. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
coin